Horizontal multistage pump manufacturer-www.guomeipump.cn

DG type Boiler Feed Pump is multi-stage,segmental centrifugal pump.The pump is a high efficiency&energy-saving product and is specially designed for new series of industrial steam boiler.It is not only used for feed water of low-middle boiler but also suitable for pumping high lift water.The temperature of the liquid is -20°C~105°C.The maximum inlet pressure is not allowed more than 0.59Mpa(6kgf/cm2)

Product name : DG horizontal multistage pump , boiler feed pump

Item : High pressure multistage pump( horizontal and vertical type)

Features :

---Segmental type high pressure pumps ---Suitable for pumping clear or slightly dirty liquids ---Direction of rotation is clockwise viewed from the drive end ---Long operational lifetime

Data sheet :

Flow: 6.3-450m3/h Head: 50-1065m Temperature: 80℃max, for boiler feed, up to 150℃

Application:

---Mining, boiler feed, feed water plants, Hot and cold water circulation, Fire fighting

Fire pump manufacturer-Shanghai Guomei Pump Co.,ltd-www.firepump.cc

The XBD-HS Series Fire Pump is designed as per NFPA20 standard, the pump is used to provide water to stand pipe, sprinkler, chemical mitigation and hydrant systems for fire suppression in industrial and commercial facilities. The performance is similar to Peerless AEF series

Product name :Split case fire pump (NFPA20 standard)

Item :electric driven, diesel dirven pump set

Features :

XBD series fire fighting pumps, including multistage pump, horizontal end suction pump, horizontal split casing pumps ,vertical inline pumps designed and manufactured in accordance with International Standard, can be motor powered and diesel powered, these pumps are ideal for fire fighting applications in harbors and wharfs, airports ), as well as ocean ships and industrial and civil high buildings. Customer's requirements shall be tailored for higher capacities and pressure.

Data sheet :

Flow: up to 12300m3/h Head: up to 200m Speed: 1480r/min, 2950r/min (50HZ)  1750r/min, 3540r/min(60HZ) Temperature: 105℃max Working pressure:2.5MPa

Application:

---Industrial and municipal water supply ---Chilled and condenser water circulating systems ---Water treatment plants ---Fire fighting ---Irrigation and sprinkler pumping stations

How to solve the problems of Split case pump -http://www.guomeipump.cn/Split-case-pumps.html

Trouble
After the pump starts, no water is sucked in, and the pointers of vacuum gauge and manometer beat heavily.
The pump doesn’t suck any water, but high vacuum is indicated on the vacuum gauge.
No water is pumped out, but high pressure is shown on the outlet manometer.
The flow rate is decreasing or the head is low. 
Over consumption of the pump power.
Unexpected noises are heard and no water is sucked.
The pump vibrates heavily.
The bearing is overheated.

reason
The water poured into the pump is not enough. Leakage of air is found the suction pipe. The foot valve is not opened. The resistance of suction is too high. The suction head is too high. The rotary direction is not right. The suction resistance is too high. The impeller flow channel is clogged. The number of revolutions is inadequate. The impeller flow channel or inlet pipe and outlet pipe are clogged. The seal ring or the impeller is worn out. The running speed of the pump is lower than the rated.
Packing is too tight and the impeller is rubbed by double suction seal ring. The flow rate is too large.
The suction resistance is excessive. The suction head is too high. Leakage of air is found from the suction pipe.
The impeller is not balanced The pump shaft is not concentric with the motor. The nuts of foundation are loose. The grease is not enough or too much or turns rotten. The pump and the motor shaft is not concentric.
Remedy
Pour water into the pump again. Block the leaking place. Open or renew the foot valves. Clean or renew the suction pipe. Make the suction head lower. Change the rotary direction. Check the length of the pipe. Clean the impeller. Increase the number of revolutions. Clean the impeller and pipes. Replace the worn parts. Increase the number of revolutions. Loosen the packing gland. Clear up the mechanic friction. Turn the discharge valve smaller. Check the pipe and the foot valve. Make the suction head lower . Block the leaking place. Adjust the discharge brake valve under specific working condition. Correct static balance of impeller. Correct the coaxial degree between pump and motor shaft. Screw the nuts of the foot bolts tightly. Check the bearing and replace the oil. Correct the coaxiality of the pump and the motor shaft

How to solve the problems of Horizontal multistage pump -www.gm-pumps.com

D type horizontal multistage pump  is applied to transport clear water or some other liquids with physical and chemical properties similar to clear water. it is widely applied in plant and city water supply

If there is problem for the pump, how to solve it? today the engineer of Shanghai Guomei Pump Co.,ltd will give some suggestions:

1. If the pump doesn't suck water, the points of the pressure gauge and vacuum gauage slings violently, then check the foot valve to see whether there is water leakage and then adequate water shall be fed into the pump. Screw down the air leakage location

2. If there is pressure down on the pressure gauge, but there is still no water coming out of the pump,  then check or shorten the pipe, check up the motor,  wash the impeller,  speed up the rotation speed

3. If the capacity is below the requirement as designed,  then Washt he pump and pipe, replace the seal ring, speed up the rotation speed

For more suggestions, will introduce in the following articles

How to choose a slurry pump-www.guomeipump.com

Shanghai Guomei PumpCo.,ltd is professional pump manufacturer in China, today our engineer want to introduce how to choose a slurry pump

One of the key elements in  slurry pumping  is the size and nature of the solids being transported by the water and the nature of the abrasive wear it causes. As wear is a function of velocity, the pumps usually operate at 1200 rpm or slower.

The slurry pump used in slurry handling are basically conventional water pumps modified in a variety of ways to handle the particular solids. While some of these modifications are minimal, some of them are quite extensive. The difference depends on the size and nature of the solids being handled.

materials of construction are  include metal liners and/or wear plates with Ni-Hard) and heat-treated high chrome iron, usually A05, sometimes, A49 for high corrosive liquid, Natural rubber and other elastomers are also frequently used as a liner for abrasive services as long as they are chemically compatible with the slurry.

In addition to centrifugal designs, there are also vertical ,submersible pumpcan meet the demand, we will introduce it in the following articles